Futaba 14MZ Manual do Utilizador Página 92
- Página / 127
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ELEVATOR
ELEVATOR 2
V-TAIL
ELEVATOR
ELEVATOR 2
AILEVATOR
FLP 2
(Camber Flap)
FLP 1
(Camber Flap)
● Mixing curve setting
(For a description of the curve setting method, see the
description at the back of this manual.)
● Fine tuning VR setting
●Return to Model Menu
Camber FLP to ELE
[Corresponding model type]: Airplane/glider, 2 ailerons + 1 flap or
more
This mixing is used to correct changes (elevator
direction) generated when the camber fl aps (speed
fl aps) are used.
● The elevator servos up side/down side rate can be
adjusted. When the mixing direction is reversed
by the linkage, adjustments can be made by
changing the mixing rate polarity.
● A mixing curve can be set.
● Mixing during fl ight can be turned ON/OFF by
setting a switch. (Always ON at NULL setting)
● The mixing rate can be fi ne-tuned by setting a VR.
● Touch the [Camber FLP to ELE] button in
the Model Menu to call the setup screen
shown below.
*The display screen is an example. The actual screen
depends on the model type.
●Curve display mode switching
(Single/Fine tuning/All Cond.)
●Elevator rate adjustment
● Group/single mode switching
(Gr./Sngl)
(For more information, see the description
at the back of this manual.)
● Overall
adjustment
by Rate A
and Rate B
Setting method
● Touch the ACT button and set the function to
ACT(ON).
● When setting a switch, touch the switch button
to call the <Switch> screen, and then select the
switch and set its ON direction. (Always ON at
"NULL" setting)
(For a description of the switch setting method,
see the description at the back of the manual.)
● Touch the elevator servos left and right buttons
and adjust the mixing rate with the adjustment
buttons displayed on the screen.
*When the mixing direction is reversed by the linkage,
adjustments can be made by changing the mixing rate
polarity.
● When setting a VR, touch the Fine tuning "NULL"
button to call the <Switch> screen, and then
select the VR.
The VR operation mode can be selected.
● A mixing curve can be set.
(For a description of the curve setting method, see
the description at the back of this manual.)
●The curve operation mode can be changed.
Single : Displays only the mixing curve
Fine Tuning : Displays the adjustment rate of the
ine tuning VR
All Cond. : Displays the mixing curve of all the
conditions (when conditions are set)
92
<Model Menu (Airplane/Glider Functions)>
- INSTRUCTION MANUAL 1
- TABLE OF CONTENTS 2
- INTRODUCTION 4
- IN NORTH AMERICA 4
- OUTSIDE NORTH AMERICA 4
- Definitions of Symbols 6
- BEFORE USE 9
- <Before Use> 11
- Transmitter controls 13
- Receiver nomenclature 22
- (Helicopter)(Airplane/Glider) 23
- ●Use rubber band to stretch 23
- BASIC OPERATION 24
- Home screen 28
- Music playback 29
- SYSTEM MENU 30
- Student mode 32
- Date and Time 34
- User Name 35
- H/W Reverse 37
- Information 38
- MODEL BASIC SETTING PROCEDURE 39
- Use in rolls 41
- Use in auto rotation 41
- C. Pitch to RUD mixing (Hold) 44
- ●Other settings 44
- FUNCTIONS OF LINKAGE MENU 50
- Servo Monitor 51
- Model Select 52
- Model Type 53
- Picture 55
- Frequency 58
- Function 59
- Trim change 60
- <Linkage Menu> 60
- Sub-Trim 61
- Servo Reverse 62
- Fail Safe 63
- End Point (ATV) 64
- Throttle Cut 65
- Idle Down 66
- <Lap time list> 69
- Dial Monitor 70
- Data Reset 71
- MODEL MENU (COMMON FUNCTIONS) 72
- Condition Select 73
- AFR (D/R) 75
- Prog. Mixes 77
- Setting methods 78
- Fuel Mixture 79
- Model Menu functions list 80
- ( ) 81
- AIL Differential 82
- Flap setting 83
- AIL to Camber FLP 84
- AIL to Brake FLP 85
- AIL to RUD 86
- Airbrake to ELE 87
- RUD to AIL 88
- Camber Mix 89
- Setting method 90
- ELE to Camber 91
- Camber FLP to ELE 92
- Butterfl y 93
- ● Mixing curve setting 94
- ● Servo speed setting 94
- Trim Mix 1/2 95
- Airbrake 97
- Ailevator 101
- ( ) 102
- RUD to ELE 104
- Snap Roll 105
- Multi Engine 106
- MODEL MENU (HELICOPTER) 107
- PIT Curve/Pitch Trim 108
- ● Hovering pitch 109
- ● Low/High pitch trim 109
- ● Adjusts the adjusting dial 109
- ● Return to Model Menu 109
- THR Curve/Throttle Hover trim 111
- Throttle Hover trim 112
- Acceleration Mixing 113
- Throttle Hold 114
- Swash mixing 115
- Throttle mixing 116
- PIT to Needle mixing 117
- Gyro mixing 119
- Governor mixing 120
- Curve setting operation 123
- Switch selection method 126
Manuais e produtos relacionados com Acessórios de comunicações Futaba 14MZ
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.295 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais