Futaba 14MZ Manual do Utilizador Página 120
- Página / 127
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Governor mixing
This is used to switch the RPM of the helicopters
head. Up to 3 rates can be set for each condition.
*The governor is used by connecting the governor speed
setting channel to CH7 (initial setting).
*When using an independent governor [ON]/[OFF] switch,
connect the AUX([ON]/[OFF]) connector of the governor to
CH8 (initial setting) and set the switch to CH2 (Governor2)
at the Function menu of the Linkage Menu.
● Return to Model Menu
● Touch the [Governor] button of the Model
Menu to call the setup screen shown below.
Setting method
● Touch the [INH] button of the rate to be used and
display [ON].
● When you want to set the same contents at other
functions, select the group mode (Gr.). When you
want to set the selected condition only, select the
single mode (Sngl).
● Three speeds (rates) can be set for each condition.
(Rate 1/Rate 2/Rate 3)
Also, this mixing and the governor side speed
setting must be matched beforehand by the
following method:
● Set so that when the governor side is placed in
the speed setting item state and [2000rpm] of
Set GOV of the screen above is touched, the
governor speed is set to "2000", when the [1500rpm]
button is touched, the governor speed is set to
"1500", and when the [1000rpm] button is touched,
the governor speed is set to "1000".
*When using the Fuel Mixture function, the mixture servo
is controlled from the governor. When transmitting the
mixture curve data from the transmitter to the governor, the
governor AUX (m.trm) connector must be connected to CH8
(initial setting) and governor side setting performed. See the
governor instruction manual.
Note: Always set (Act) and (Trim) to [NULL] for
[Governor] and [Governor 2] of the Function menu.
● When you want to read the speed directly, press
the [%] button and display [rpm].
● The speed can be witched by setting a switch.
Also, when [OFF] is set instead of speed setting,
the governor can be turned [ON]/[OFF] without
setting a separate [ON]/[OFF] switch.
● A speed fi ne tuning VR can be set.
*VR selection, adjustment width, and adjustment direction
can be set.
120
<Model Menu (Helicopter Functions)>
- INSTRUCTION MANUAL 1
- TABLE OF CONTENTS 2
- INTRODUCTION 4
- IN NORTH AMERICA 4
- OUTSIDE NORTH AMERICA 4
- Definitions of Symbols 6
- BEFORE USE 9
- <Before Use> 11
- Transmitter controls 13
- Receiver nomenclature 22
- (Helicopter)(Airplane/Glider) 23
- ●Use rubber band to stretch 23
- BASIC OPERATION 24
- Home screen 28
- Music playback 29
- SYSTEM MENU 30
- Student mode 32
- Date and Time 34
- User Name 35
- H/W Reverse 37
- Information 38
- MODEL BASIC SETTING PROCEDURE 39
- Use in rolls 41
- Use in auto rotation 41
- C. Pitch to RUD mixing (Hold) 44
- ●Other settings 44
- FUNCTIONS OF LINKAGE MENU 50
- Servo Monitor 51
- Model Select 52
- Model Type 53
- Picture 55
- Frequency 58
- Function 59
- Trim change 60
- <Linkage Menu> 60
- Sub-Trim 61
- Servo Reverse 62
- Fail Safe 63
- End Point (ATV) 64
- Throttle Cut 65
- Idle Down 66
- <Lap time list> 69
- Dial Monitor 70
- Data Reset 71
- MODEL MENU (COMMON FUNCTIONS) 72
- Condition Select 73
- AFR (D/R) 75
- Prog. Mixes 77
- Setting methods 78
- Fuel Mixture 79
- Model Menu functions list 80
- ( ) 81
- AIL Differential 82
- Flap setting 83
- AIL to Camber FLP 84
- AIL to Brake FLP 85
- AIL to RUD 86
- Airbrake to ELE 87
- RUD to AIL 88
- Camber Mix 89
- Setting method 90
- ELE to Camber 91
- Camber FLP to ELE 92
- Butterfl y 93
- ● Mixing curve setting 94
- ● Servo speed setting 94
- Trim Mix 1/2 95
- Airbrake 97
- Ailevator 101
- ( ) 102
- RUD to ELE 104
- Snap Roll 105
- Multi Engine 106
- MODEL MENU (HELICOPTER) 107
- PIT Curve/Pitch Trim 108
- ● Hovering pitch 109
- ● Low/High pitch trim 109
- ● Adjusts the adjusting dial 109
- ● Return to Model Menu 109
- THR Curve/Throttle Hover trim 111
- Throttle Hover trim 112
- Acceleration Mixing 113
- Throttle Hold 114
- Swash mixing 115
- Throttle mixing 116
- PIT to Needle mixing 117
- Gyro mixing 119
- Governor mixing 120
- Curve setting operation 123
- Switch selection method 126
Manuais e produtos relacionados com Acessórios de comunicações Futaba 14MZ
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 1.232 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais